Strategy 2: Iterative Optimization
Overview
Dispense, measure, adjust, repeat until target is met.
This strategy treats material handling as an optimization problem: perform a trial dispensing, measure the outcome, adjust parameters based on the measurement, and repeat until accuracy requirements are met.
When to Use
- High accuracy required (±0.5% or better)
- Model is uncertain (don't trust first-principles calculations)
- Material variation is high between batches or within a batch
- Feedback sensors available (balance, fill-height camera, pressure transducer)
- Computational resources are modest (linear model, not deep learning)
- Time budget allows for multiple dispense cycles (3–10 iterations typical)
How It Works
Step 1: Initial Guess
Start with a nominal parameter set: - From a prior model (Strategy 1) - From literature or manufacturer data - From past similar material
Example: Dispense first 5 g of powder at speed = 50 rpm (nominal).
Step 2: Measure Outcome
After each dispensing, measure what was actually delivered:
- Gravimetric: Place collection vessel on balance, measure mass
- Volumetric: Use graduated cylinder or measure volume change
- Fill height: Use camera to estimate volume from fill height in container
- Pressure/flow: Monitor pressure drop or flow rate during extrusion
Accuracy: Measurement must be at least 5× more accurate than your final tolerance. (For ±1% target, measure to ±0.2%.)
Step 3: Compute New Parameters
Use the error to estimate a better parameter set:
Linear Model (Most Common)
If outcome is linear in the parameter:
Example:
- Trial 1: dispense at speed S₁ = 50 rpm → measure M₁ = 4.8 g
- Target: 5.0 g
- Error: ΔM = 5.0 − 4.8 = 0.2 g (too low)
- Sensitivity: Assume ΔM / ΔS ≈ 0.1 g/rpm
- New speed: S₂ = S₁ + ΔM / sensitivity = 50 + 0.2 / 0.1 = 52 rpm
Quadratic or Non-Linear Model
For non-linear systems, use: - Polynomial fit if you have 3+ data points - Gaussian process regression if you have time and want confidence intervals - Neural network if you have 20+ historical examples
Step 4: Repeat Until Converged
Dispense again at S₂, measure M₂, adjust to S₃, etc.
Convergence criterion: When |M_{n+1} − target| < tolerance, stop.
Typical trajectory:
Trial 1: M = 4.8 g (1.8 mg short) → update model
Trial 2: M = 5.05 g (0.5 mg over) → refine
Trial 3: M = 4.99 g (0.1 mg short) → PASS
Advantages
| Aspect | Benefit |
|---|---|
| Accuracy | Can achieve ±0.5–1% accuracy even with unknown material |
| Robustness | Automatically corrects for drift, temperature, batch variation |
| Model-free | No need to measure physical properties or fit a complex model |
| Adaptive | Learns the relationship on the fly for each material |
| Failure recovery | If first trial is wrong, subsequent trials correct it |
Limitations
| Challenge | Issue |
|---|---|
| Time | Takes 3–10 dispense-measure cycles (10–30 minutes typical) |
| Waste | Each trial uses material; can add up for expensive substances |
| Non-linearity | If relationship is highly non-linear, may not converge or overshoot |
| Measurement noise | If balance is noisy (±0.05 g), errors propagate |
| Parameter constraints | May try to set pump speed or pressure outside hardware limits |
Real-World Examples
Example 1: Powder Dispensing by Weight
Task: Dispense 1.0 g of API (Active Pharmaceutical Ingredient) powder, 20 times
Procedure:
- Set auger feeder to nominal 30 rpm
- Dispense trial 1 → weigh → 0.95 g (50 mg short)
- Model: ΔM = 1.7 mg/rpm
- Update: speed₂ = 30 + 50/1.7 ≈ 30 rpm (negligible change, but be patient)
- Dispense trial 2 → 1.01 g (PASS)
- Dispense 20 final doses at 30 rpm
- Each dose: 1.0 ± 0.02 g
Time: ~5 minutes for calibration + 5 minutes for 20 doses.
Alternative (faster): Dispense 3–5 trials to map the sensitivity curve, then all 20 final doses at optimized speed.
Example 2: Liquid Volume in Syringe Extrusion
Task: Extrude 1.0 mL of silicone polymer ink onto a 3D printing substrate
Procedure:
- Set motor speed to 10 mm/s plunger speed
- Dispense trial 1 → measure bead volume (via image analysis) → 0.92 mL (80 µL short)
- Sensitivity: 8 µL/mm/s
- Speed₂ = 10 + 80/8 = 20 mm/s (Too aggressive? Try 15 mm/s for safety)
- Dispense trial 2 at 15 mm/s → 1.03 mL (PASS, or close)
- Adjust to 14.5 mm/s if needed
- Dispense 5 final beads at 14.5 mm/s
- Each bead: 1.0 ± 0.05 mL
Measurement: Use calibrated syringe or optical measurement.
Example 3: Paste Extrusion with Pressure Control
Task: Extrude 2 mL of ink at consistent flow rate
Procedure:
- Air-pressure syringe set to 200 kPa nominal
- Trigger extrusion, measure extrusion time for 2 mL → 4.5 seconds (faster than expected)
- Flow rate: 2 mL / 4.5 s = 0.44 mL/s
- Target flow rate: 0.4 mL/s (slower, for precision)
- Pressure sensitivity: 0.05 mL/s per 10 kPa
- Required pressure: 200 − 10×0.04/0.05 ≈ 192 kPa
- Adjust to 190 kPa and retry
- Measure extrusion time → 5.0 seconds (0.40 mL/s) ✓ PASS
Linear Calibration Model (Most Practical)
For most dosing tasks, a linear 1-parameter model suffices:
Calibration Procedure
- Collect 3 data points at different settings:
- Setting A: dose_A
- Setting B: dose_B
-
Setting C: dose_C
-
Fit the line: $$ \beta = \frac{(\text{dose}_B - \text{dose}_A)}{(\text{setting}_B - \text{setting}_A)} $$ $$ \alpha = \text{dose}_A - \beta \times \text{setting}_A $$
-
Predict setting for target dose: $$ \text{setting} = \frac{\text{target_dose} - \alpha}{\beta} $$
-
Execute at predicted setting.
-
(Optional) Fine-tune: If measured dose differs from target by > 2%, adjust once more.
Example Calibration Table for Powder Auger
| Auger Speed (rpm) | Measured Dose (g) |
|---|---|
| 40 | 0.90 |
| 50 | 1.10 |
| 60 | 1.30 |
Fit: slope β = (1.30 − 0.90) / (60 − 40) = 0.02 g/rpm, intercept α = 0.90 − 0.02×40 = 0.10 g
Target: 1.00 g → setting = (1.00 − 0.10) / 0.02 = 45 rpm
Verify: At 45 rpm, expect (0.10 + 0.02×45) = 1.00 g ✓
Implementation Checklist
- [ ] Define target dose and tolerance (e.g., 5.0 ± 0.1 g)
- [ ] Choose measurement device (balance, camera, flow meter) and verify accuracy
- [ ] Start with nominal parameter (literature, prior data, or guess)
- [ ] Dispense trial 1, measure outcome
- [ ] If within tolerance, proceed to main task; if not, continue
- [ ] Fit linear model (or use proportional control if only one trial)
- [ ] Predict next parameter value
- [ ] Dispense trial 2, measure
- [ ] Repeat until within tolerance (typically 2–4 iterations)
- [ ] Document calibration for future reference
- [ ] Dispense all final doses at optimized parameter
- [ ] Verify final doses meet specification
Comparison with Other Strategies
| Strategy | Time to Deploy | Accuracy | Robustness | Sensor Requirement |
|---|---|---|---|---|
| Characterize, then act | Very fast (1 min) | ±5% | Low | Minimal |
| Iterative optimization | Medium (10–20 min) | ±1% | High | Balance, scale |
| Real-time correction | Medium (5–10 min) | ±1–2% | Very high | Fast sensor |
| Feedforward prediction | Very fast (1 min) | ±2% | Medium | Rheometer, model |
References
- Hastie, T., Tibshirani, R., & Friedman, J. (2009). The Elements of Statistical Learning. Springer.
- Box, G. E., Hunter, W. G., & Hunter, J. S. (1978). Statistics for Experimenters. Wiley.
- Rastegardoost et al. (2026). Iterative optimization in autonomous dispensing systems. Lab on a Chip.